New Electric Water Heater
We supply Rheem, A.O. Smith, Bradford White, or State Water Heaters tanks in the size that fits your household. You choose the warranty tier, from six to twelve years, and we install it the same day.
Licensed plumbers, same-day installs, code-correct work
Electric Water Heater Installation Littleton CO Done Right
When your electric water heater quits, you need Electric Water Heater Installation Littleton CO homeowners can count on. We install Rheem, A.O. Smith, and Bradford White tanks sized for your home, pull the permit, and restore hot water the same day in most cases. From Downtown Littleton to Ken Caryl, our licensed plumbers handle every connection, test, and cleanup.
Careful work. Honest options.
About this service
Electric Water Heater Installation Littleton CO
Electric Water Heater Installation Littleton CO is the licensed removal of your old tank and the code-compliant installation of a new electric water heater, including the electrical connection, plumbing tie-ins, pressure relief valve, expansion tank, and permit inspection. We drain the old unit, disconnect the wiring, set the new tank, and test every connection before we leave. Most installs take three to five hours from arrival to hot water.
Littleton homes face hard water that builds sediment and scale inside tanks, shortening their life to eight or ten years. When yours starts leaking, popping, or running out of hot water, waiting rarely helps. We handle electric water heater replacement Littleton CO residents schedule before a failed tank floods a basement or garage. Whether you need a 40-gallon unit for a Grove Street bungalow or an 80-gallon tank for a Governor's Ranch family of five, we size it right.
- ✓ Same-Day Hot Water
- ✓ Code-Correct Permits
- ✓ Right-Sized Tanks
- ✓ Warrantied Workmanship
What's included
What Our Electric Water Heater Installation Includes
Every install includes the tank, labor, permit, and cleanup. Here is what is covered so you know exactly what you are paying for.
Permit and Inspection
We pull the Littleton plumbing permit and meet the inspector on site. The install is code-compliant under NEC and Uniform Plumbing Code, and you get documentation for your records.
Pressure Relief Valve and Expansion Tank
Every install includes a new pressure relief valve and, where required, an expansion tank. These protect your tank and plumbing from thermal expansion and overpressure.
Electrical Connection
We verify your panel has capacity, run the correct wire gauge, and connect the tank to code. A multimeter and thermostat tester confirm proper voltage and element function before we leave.
Old Tank Haul-Away
We drain and remove your old tank, then haul it away for recycling. You do not need to move it, schedule a pickup, or pay a disposal fee separately.
Walkthrough and Warranty
We show you the thermostat setting, explain the anode rod maintenance schedule, and hand you the warranty paperwork. You know how to get the most life out of your new tank.
How it works
What to Expect During Installation
We ask about your current tank size, household count, and symptoms. You get an upfront price range before we roll a truck, and we schedule a two-hour arrival window that same day or next.
Our plumber checks your electrical panel for available amperage, verifies the breaker and wire gauge, and measures the space. We confirm the tank size and model, then hand you a firm written price before any work starts.
We shut off power and water, drain the old tank with a hose, and disconnect the wiring and plumbing. The old unit comes out, the area gets cleaned, and we inspect the pan and drain for damage.
We set the new tank, connect the cold and hot lines, install the pressure relief valve and expansion tank, and wire the unit to code. A multimeter and thermostat tester confirm proper voltage and element function before we fill the tank.
We fill the tank, purge air, restore power, and verify hot water at every fixture. You get a walkthrough of the thermostat setting, the anode rod schedule, and the warranty paperwork before we leave.
STEP 01Phone Assessment
We ask about your current tank size, household count, and symptoms. You get an upfront price range before we roll a truck, and we schedule a two-hour arrival window that same day or next.
Tools & methods
Tools and Methods We Use
Pipe Wrench
Used to break loose and tighten threaded fittings on the cold and hot water lines without damaging the pipe.
Tube Cutter
Cuts copper tubing cleanly for precise fits when we modify or replace supply lines during installation.
Multimeter
Tests voltage at the tank and verifies the heating elements and thermostat are receiving correct power.
Thermostat Tester
Confirms the thermostat is reading and controlling temperature accurately before we hand the job over.
Anode Rod Socket
Removes and installs the anode rod during maintenance or when we inspect tank corrosion on older units.
Water Heater Element Wrench
Removes and tightens heating elements without rounding the hex head, which prevents leaks at the element gasket.
Real results
Before and after.
Electric Water Heater Installation
Leaking 12-Year-Old Tank Replaced
A 50-gallon electric tank in a Downtown Littleton home was leaking from the bottom and leaving a puddle in the basement. The homeowner was mopping daily and worried about water damage.
After: We installed a new 50-gallon Rheem with a brass drain valve, new pressure relief valve, and expansion tank. The install took four hours, passed inspection the next day, and the basement floor is dry.
Book this service →
Electric Water Heater Installation
Undersized Tank Upgraded for Family of Five
A Ken Caryl family kept running out of hot water with a 40-gallon tank. Morning showers were staggered, and the dishwasher and laundry competed for hot water.
After: We upgraded to a 65-gallon electric tank and replaced the 30-amp breaker with a 40-amp circuit. First-hour rating jumped from 55 to 78 gallons. The family now runs three showers back to back without a drop in temperature.
Book this service → Electric Water Heater Installation
Failed Heating Element Replaced, Tank Saved
A Governor's Ranch homeowner had lukewarm water and a tripped breaker. The lower heating element had shorted, and the tank was only six years old.
After: We tested both elements with a multimeter, replaced the failed lower element and thermostat, and flushed the tank. The repair cost a fraction of a new install, and hot water was back in two hours.
Book this service → Problems we solve
Problems We Solve With New Installation
When your electric water heater fails, the symptoms are predictable. Here is what we fix and how we fix it.
Ask a pro →No hot water at all
We test both elements and thermostats with a multimeter. If the tank is sound, we replace the failed part. If the tank is old or corroded, we install a new electric water heater the same day.
Rusty or metallic-tasting hot water
We inspect the anode rod and tank interior with an inspection camera. If corrosion is advanced, we replace the tank. If caught early, we replace the anode rod and flush the tank.
Popping or rumbling sounds
We flush the tank and, when needed, use a descaling pump to clear stubborn scale. If the tank is near end of life, we install a new one and set you up on a flush schedule.
Leaking tank or T&P valve
We diagnose the leak source. A failed T&P valve or drain valve is repairable. A corroded tank gets replaced with a new electric water heater, including a new valve and expansion tank.
Proof you can check
Licensed, Certified, and Reviewed
- Colorado Master Plumber License · State of Colorado
- EPA Lead-Safe Certified · U.S. Environmental Protection Agency
- NATE Certified · North American Technician Excellence
- OSHA 10 · Occupational Safety and Health Administration
- Backflow Prevention Certification · State of Colorado
Most electric water heater installations in Littleton run $850 to $1,800 in 2026, including the tank, labor, permit, and haul-away. A basic 40-gallon swap sits near the low end; a larger tank, panel upgrade, or expansion tank add-on pushes toward the high end. We give you a firm price before work begins.
A standard electric tank swap takes three to five hours from arrival to hot water. If we need to upgrade the electrical circuit or add an expansion tank, plan on five to seven hours. We schedule a two-hour arrival window and call ahead when we are on the way.
Littleton Plumbing Solutions installs electric water heaters across Littleton and Arapahoe County. Our plumbers hold a Colorado Master Plumber License and pull the required permit for every install. We serve ZIP codes 80120, 80122, 80123, 80128, and surrounding areas.
Yes. Littleton requires a plumbing permit for water heater replacement, and the work must pass inspection. We pull the permit, schedule the inspection, and meet the inspector on site. Skipping the permit can void your warranty and create problems when you sell your home.
Ready when you are
Get Your Electric Water Heater Installation Littleton CO
Call Littleton Plumbing Solutions for same-day electric water heater installation. Licensed plumbers, upfront pricing, permits handled, and hot water back the same day in most cases. We serve all of Littleton and Arapahoe County.
Schedule Installation +13038790886 →
Request an appointment
Contact Littleton Plumbing Solutions
Call us at +1 303-879-0886 or send an email to info@littletonplumbingsolutions.com. We answer the phone 24/7 for emergencies and book regular service Monday through Friday. Most calls get a same-day slot, and we will give you a real arrival window, not a four-hour block.
Call anytime+13038790886Email the officeinfo@waterheaterrepairlittleton.com
Office hoursOpen 24 hours · 7 days a week