When your hot water quits, you need Water Heater Repair in Aurora that shows up fast and fixes it right. We serve Original Aurora, Heather Gardens, Southlands, and every ZIP from 80010 to 80047. Our licensed techs carry parts for Rheem, A.O. Smith, and Bradford White on every truck. One call, and we get your hot water back.
Licensed · Upfront options · Clean work areas · Written guarantees
Aurora's mix of old and new housing keeps demand high for both repairs and replacements. Hard water wears out tanks faster here, so we do a lot of sediment removal and anode rod work. Whether you need affordable Water Heater Repair in Aurora or a full system swap, we handle it. Our trucks cover every neighborhood from Original Aurora to the Southlands area.
New installs in Aurora run from 40-gallon gas tanks in Original Aurora bungalows to 75-gallon units in Saddle Rock. We pull permits, set the expansion tank, and test the pressure relief valve before we leave. Most installs finish in three to four hours.
View details ↗02When your tank is rusted through or leaking from the base, replacement beats repair. We haul out the old unit, match the new one to your home's gas line or panel, and recycle the old tank. Same-day replacement is common in Aurora when we have the size on the truck.
View details ↗03Scale buildup is the top killer of tankless units in Aurora. We descale with a pump and vinegar solution, clear error codes, and test the igniter and gas valve. Navien and Rinnai units are on most of our trucks' parts lists.
View details ↗04Tankless installs in Aurora need a dedicated gas line and proper venting. We size the unit to your household, run the stainless vent, and set the recirculation if you want instant hot water. New builds near 80018 are our most common tankless jobs.
View details ↗05Annual descaling keeps tankless units alive in Aurora's hard water. We flush the heat exchanger, clean the inlet filter, and check the igniter and flame sensor. One visit a year prevents the scale that causes most no-hot-water calls.
View details ↗06Tank repairs in Aurora cover everything from a broken heating element to a failed thermocouple. We test the thermostat, check the dip tube, and inspect the anode rod. Most tank repairs finish in one visit with parts we carry on the truck.
View details ↗07We install Rheem, A.O. Smith, and Bradford White tanks across Aurora. Proper sizing matters in older homes with low gas pressure. We check the gas valve, set the temperature, and make sure the T&P valve discharges safely.
View details ↗08Gas repairs in Aurora often trace back to a dirty thermocouple, a failing gas valve, or a pilot that will not stay lit. We test with a multimeter and replace only what failed. Cold winters here make pilot issues more common from November through March.
View details ↗09Gas installs require correct venting and a proper gas valve. We run the flue to code, check for leaks with a pressure gauge, and confirm the thermocouple reads correctly. Most Aurora gas installs take three to five hours.
View details ↗10Electric repairs in Aurora usually mean a burned-out heating element or a bad thermostat. Hard water shortens element life, so we check both elements and the thermostat. We carry element wrenches and replacement parts for common brands.
View details ↗11Electric installs need the right breaker size and a proper ground. We check your panel, run the circuit to code, and set the thermostat. Older Aurora homes sometimes need a panel upgrade before we can install a larger tank.
View details ↗12Heat pump water heaters cut energy bills, but they need space and a drain for condensate. We size the unit, set the condensate line, and configure the operating modes. These installs work well in Aurora's newer, well-insulated homes.
View details ↗13Solar water heater repairs in Aurora cover pump failures, sensor faults, and scale in the collector loop. We test the controller, flush the loop, and check the pressure relief valve. Solar systems need service every few years to keep performing.
View details ↗14Solar installs in Aurora need good sun exposure and a backup tank for cloudy weeks. We mount the collectors, run the loop, and set the controller. Colorado's sunny days make solar a solid fit for many Aurora homes.
View details ↗15Annual tune-ups in Aurora include flushing sediment, testing the T&P valve, and checking the anode rod. We also test the thermostat and inspect the gas valve on gas units. One visit a year adds years to your tank's life.
View details ↗16Aurora's hard water leaves scale fast. We flush the tank, descale the elements, and clear sediment from the drain valve. Tankless units get a pump descale with vinegar. Most flushes take 60 to 90 minutes.
View details ↗17The anode rod sacrifices itself to protect your tank. In Aurora's water, it can be gone in three to five years. We pull the old rod with an anode rod socket, inspect the tank, and install a new one. This is the cheapest way to extend tank life.
View details ↗18A faulty thermostat means no hot water or scalding water. We test both elements and the thermostat with a multimeter. Replacement is quick, and we set the temperature to 120 degrees for safety and efficiency.
View details ↗19Burned-out elements are common in Aurora electric tanks. Hard water coats the element in scale until it overheats and fails. We pull the old element with an element wrench, flush the tank, and install a new one.
View details ↗20A pilot that will not stay lit usually means a bad thermocouple or a dirty orifice. We clean the assembly, test the thermocouple, and replace the igniter if needed. This is one of the most common gas calls we get in Aurora.
View details ↗21Gas valve failure means no heat and sometimes a gas smell. We test the valve, check the thermocouple, and confirm the gas pressure. A new gas valve restores normal operation, and we leak-test the connection before we leave.
View details ↗22A leaking T&P valve or a failed pressure relief valve is a safety issue. We test the valve, check the expansion tank, and replace the valve if it is stuck. We also verify the discharge pipe runs to code.
View details ↗23A failed expansion tank causes pressure spikes and T&P valve leaks. We install a new tank on the cold line, set the pre-charge pressure, and test the system. This is a quick job that prevents bigger problems.
View details ↗24Leaks come from the drain valve, the T&P valve, the fittings, or a cracked tank. We find the source with an inspection camera, fix what we can, and tell you straight if the tank is done. A cracked tank means replacement.
View details ↗25Sediment builds up in every Aurora tank. It causes popping sounds, reduces capacity, and shortens tank life. We flush the tank, clear the drain valve, and remove the buildup. Annual sediment removal is the best cheap insurance.
View details ↗26A clogged or leaking drain valve makes flushing impossible. We replace the valve, clear the sediment, and test the drain. Plastic valves break easily, so we install brass replacements that last.
View details ↗27A failed igniter means no hot water on a gas unit. We test the igniter, check the flame sensor, and replace the part if needed. Most igniter repairs finish in under an hour.
View details ↗28A clogged toilet in Aurora is often a main line issue, not just a local clog. We snake the line, camera the pipe, and clear the blockage. If the main is failing, we can replace it before it backs up again.
View details ↗29Old galvanized and polybutylene lines fail in Aurora's older neighborhoods. We trench, replace the line with PEX or copper, and restore the yard. Most replacements finish in one to two days.
View details ↗Every Water Heater Repair Aurora CO job starts with a real diagnosis, not a guess. We test the thermostat, check the heating element, and inspect the anode rod before we quote anything. In Aurora's older homes, we often
Scale coats heating elements and heat exchangers, causing overheating, popping sounds, and early failure. Aurora's water is harder than the metro average, so units here fail sooner than in softer-water areas.
We descale tankless units with a pump and vinegar, flush tanks to clear sediment, and recommend annual maintenance. For electric tanks, we pull the element and clean it before it burns out.
Book a visit →
From November through March, Aurora sees single-digit nights. Cold makes thermocouples and gas valves work harder, and pilot lights go out more often. No-hot-water calls spike in winter.
We test the thermocouple and gas valve on every winter call. If the pilot will not stay lit, we replace the thermocouple and clean the orifice. We also check the venting for blockages from snow or ice.
Book a visit →
Original Aurora has 1920s homes with galvanized lines. Saddle Rock has 1990s builds with polybutylene. Each era needs different parts and approaches. A one-size repair does not work here.
We stock parts for both old and new systems. On older homes, we check the gas line size and venting before installing a new tank. On newer homes, we match the unit to the existing setup.
Book a visit →01Popping or rumbling sounds from the tank
02Rusty or metallic-smelling hot water
03Water pooling around the base of the tank
04Pilot light keeps going out
05Hot water runs out faster than it used to
Aurora is a big city, and knowing the landmarks helps us get to you faster. We route around Anschutz Medical Campus traffic, use the Aurora Municipal Center as a central reference, and know the Southlands Mall area well. Cherry Creek State Park marks the western edge of our Aurora coverage. These landmarks help us plan the quickest route to your door.
This campus sits in north Aurora near Colfax and Peoria. We use it as a reference point for calls in the 80045 ZIP and nearby neighborhoods. Traffic patterns here matter for scheduling.
The Municipal Center is near Alameda and Chambers, close to the city's geographic center. It helps us orient calls in the 80012 and 80014 ZIPs. We know the surrounding streets well.
Southlands Mall anchors the southeast part of Aurora near E-470 and Smoky Hill Road. It is a key reference for calls in the 80016 ZIP. We know the access roads and shopping center traffic.
The park marks Aurora's western edge along I-225. It helps us plan routes for calls near the 80014 and 80015 ZIPs. We know which roads get backed up on weekends.
These are our most frequently served ZIP codes. Nearby areas may also qualify—call if you do not see yours.
Original Aurora · Heather Gardens · Southlands · Saddle Rock
Our team can help if your question is not answered here.
Call +13038790886 →Most repairs in Aurora run $180 to $450 in 2026. A thermocouple or heating element replacement is on the low end. A gas valve or T&P valve repair is on the higher end. Tankless descaling runs $200 to $350. We quote the price before we start, so you know the cost upfront.
The best company is the one that shows up when it says it will, carries the right parts, and stands behind the work. We are licensed, insured, and NATE Certified. We serve every Aurora ZIP from 80010 to 80047. Call us and judge for yourself.
Yes. We run 24/7 emergency service for Aurora. If your tank fails at 2 a.m., call our dispatch line. We will get a tech out as fast as we can. After-hours calls carry a dispatch fee, but we quote it before we come out.
Start with a local company that knows Aurora's housing stock and water. Ask if they are licensed and insured. Check if they carry parts for your brand. We serve every Aurora neighborhood and can usually get there the same day.
Yes, in most cases. Call before noon and we can usually get a tech out the same afternoon. We stock common parts on every truck, so most repairs finish in one visit. If we need a rare part, we will tell you upfront.
Call now and talk to a real plumber, not a call center. Same-day service, upfront pricing, and a warranty on every repair. We serve all of Littleton and Arapahoe County.
Tell us what you are seeing and where you are located. Our team will call to confirm the right appointment type and timing.